Wednesday, 25 May 2022

#41 WW The Triple Fold Card - by Lisa Shaw

 Welcome to Creative Minds Kind Hearts’ 

41st Wednesday Wonder - the Triple Fold Card

By Lisa Shaw


This week sees what is possibly one of the easiest folds you will ever make, yet it is very effective once finished.





I have used an old Craftwork Cards set of papers called Countryside to decorate this card. The template below should enable you to make this card using basic cutting and measuring tools, with possibly a die or two for the embellishment.










You should be able to see here that I decorated the first two sections with the same papers, the third & fourth with another pattern and the last section with a third paper. Remember there is no hard and fast rule for this - you may want to use the same paper on each section, or five different papers - the choice is yours.

For matting and layering, I make my mat 1/4” smaller than the base card and my layer 1/4” smaller than my mat, which gives 1/8” border. This, again, can be changed if you wish to have a wider border.

For the decoration I used some square nesting dies, the smallest being 1 3/8” to the largest at 2 3/8”

To finish the card off, I mat & layered papers on the reverse of the card and used a Woodware sentiment stamp.



I hope that this will give you the inspiration to make a card in this style.


Love Lisa xx 


Tuesday, 22 February 2022

GERALDINE ENTWISTLE Z-FOLD POP UP CARD

 HOW TO CREATE A Z -FOLD POP UP CARD



YOU WILL NEED

BASE CARD 8 1/2" BY 5 1/2" SCORE AT 2 1/8" AND 4 1/4" TO CREATE A Z-FOLD CARD

FRONT RECTANGLE PANELS 2 MAT LAYERS   - 5 1/4" X 1 7/8" 

FRONT TOPPERS 2 MAT LAYERS - 1 3/4" X 1 3/4"

FRONT TOPPERS 2 WHITE CARD PIECES - 1 5/8" X 1 5/8"

MIDDLE AND BACK 2 MAT LAYERS - 2 3/4" X 2 3/4" 

MIDDLE AND BACK 2 WHITE CARD PIECES - 2 3/4"X 2 3/4" (CUT 1 PIECE DIAGONALLY) 

CORNER PANELS 2 PATTERN PIECES - 2 " X 2" (CUT DIAGONALLY)

 







TO MAKE THIS CARD



1   Stick the 2 MAT LAYERS   - 5 1/4"X 1 7/8" onto the first two panels of the z fold card base.



2.  Stick the four co-ordinating triangles ( 2 COMPLIMENTARY PIECES - 2 " X 2" CUT DIAGONALLY) to the corners of the back of the card.  I found that liquid glue makes it easier to align the triangles to the corners.


3.  Stick the square mat (2 3/4" X 2 3/4")  centrally between the four triangles.  If you are stamping onto the white layers - remember they will be diamond-shaped. I used pre-printed images.  Layer the 2 5/8" x 2 5/8" image onto this mat.


4 Take the 2 3/4" x 2 3/4" mat and score diagonally   Then cut away approximately 1" away from the tip of one corner ( as shown in the photo above). 



5.  Stick this cropped diamond onto the inside panel of the z fold. Add the image of your choice (on the 2 5/8" triangle)




6.  Stick and layer the two images on the 1 5/8" x 1 5/8" squares onto the 1 3/4" x 1 3/4" mats.  Stick the two diamonds onto the front panel.  Take care where adding glue.  Line the right-hand points up with the inside back panel.



Your card is now complete.  Please give this card a go and share your makes on our Facebook Group page.  I look forward to seeing your makes very soon.

Best wishes and happy crafting
Geraldine 


Tuesday, 21 September 2021

Nellie Melon - Double Reverse Shutter Card

Welcome to this weeks Wednesday Wonder, which is a Double Reverse Shutter card



You will need a 12" x 6" piece of cardstock

Scoring

At 2", 4", 8" and 10" score the full height of the card 

At 1", 5", 7" and 11" score to 1 inch down from the top and 1 inch up from the bottom

your score lines should be in these positions



Cutting 

Make a straight cut from the black spot to the pink spot in the four places shown in the picture

Folding 

The easiest way I found to put in the folds was to start with the scores which run from top to bottom, initially ignoring the the smaller scores which will be folded the wrong way at this stage.  Hopefully your card should look something like the picture below

Now fold in the smaller score lines along the top and bottom, reversing the two on each side which were folded the wrong way on the previous step




The fun part of decorating your card now begins!  On my sample card I have added a belly band to keep it closed but that was more because I used thick cardstock

For an alternative take on the style I also made a card using a piece cut to 10" x 6" but only put the fold and cuts on one side, when folded this will fit in a 6" x 6" envelope


Hope you enjoy trying out this style and be sure to share your cards on the main page


Have fun!

Nellie Melon

Tuesday, 14 September 2021

Cathryn Walker - Trifold Tags

As you may know I do love a good tag so today have done a little fold out tag tutorial for you, perfect for gift cards, little notes or an alternative to a card.  



My folded tags measure 3"x6" but you can adapt this to make tags as small or large as you like.  I cut a 9 3/8" x 6" sheet of card then scored along the longest edge at 3", 3 2/8", 6 2/8" and 6 3/8".


To cut the tag shape I marked 1/2" in and 1/2" down from each top corner then cut between these to remove the corners. 

I then used a chestnut brown ink around the tags front and back to give it a more vintage look. 


I then cut patterned paper from my vintage dreams paperpad into 5 tags measuring 2 3/4" x 5 3/4", 3 Small tags measuring 1 1/2" x 2 3/4" and a 1 1/2" x 6" strip of paper. 



I used 2 of the large tags to decorate the inside of the folded tag.  For the strip I layed out the small tags against the back of the paper and marked between the tags before gluing along the marked lines and sticking into the middle inside tag to make 3 slots for the little tags. 



I attached a ribbon to tie my tag so I glued this into place then secured with double sided tape before decorating the front and back covers with the other large tags. 



I also cut out two 2"x 2 3/4" rectangles then cut these diagonally to make little pockets for the inside of my tags.  I attached these by gluing along the horizontal and vertical sides and leaving the diagonal side unglued to create a "pocket" that you can use for little notes or more tags. 




Look forward to seeing all your crafty makes 😊







Tuesday, 7 September 2021

Two tents are better than one

 


Two tents are better than one!


I love easy designs that still have impact and I turn to this style time and time again. I like how it has plenty of room to write personal message inside.

You will need:

  • card blank 5 ¾ x 5 ¾ (14.5cm) or cut one from A4 card (bought as card blank)

  •  card blank 4 x 4 or cut one to 4 ¼ x 4 ¼ from card (see notes below) (10cm or 10.5cm)

  •  topper at least 4” square or diameter (10cm)
  •  scraps of design paper and contrasting paper to mat

 

This design works well for circular or square toppers but start with the one you want you use. Today I have a square topper cut from 12 x 12 sheet of Sandy paws papers designed by Helz Cuppelditch for Craft Consortium. This will fit exactly onto a premade 4” card blank or I could trim it and mat with the same contrasting paper onto a 4 ¼ “, which I decided to do.

To cut aperture:

If you have a square die 3 3/8 or 8.5cm cut this centrally into the card front, or use a scalpel or trimmer leaving a 1 1/8 or 3cm frame outside. Tip- this is exactly the width of my metal ruler. 



  
Cut strips of contrasting paper for mat layer 1” wide or 2.5 cm. I like a pinwheel effect similar to patchwork and cut them 4 1/2“ long (approx. 11.2 cm).

Check each side to ensure they fit and trim if necessary, before adhering, especially if you have die-cut the aperture.

                   

Mat (and layer) the topper onto smaller card base ensuring it is tent fold. Place this centrally inside main card, lifting and checking all correct before adding glue. I use Collall wet glue here and don’t press down, lifting outer card to check it is straight from inside too. If desired, you can add stamps to inside of card too.

Voilà!

 



         

         

 

Happy Crafting!  

Lesley



Tuesday, 31 August 2021

Three Panel Pop out card - Gill Harrop




Three Panel Pop out card.

Instructions given for a 6 inch card. See end for 5'' inch and  5 x 7'' variations.

Take a piece of 12 x 12 inch cardstock – I used 250 gsm card.

Score on one 12 inch side at 4 and 8 inches. Turn card 90 degrees and cut to a 12 x 6 inch piece. On this piece Fold .. from left side first score is mountain. Right score valley .

Decide how deep you want the ‘pop out’ panel to be. Mine is 4''. So cut remaining strip at 4 x 12 Again mountain and valley folds to match bigger piece.

Tip: Alternatively cut the 12 x 12 cardstock to 12 x 10 then score – that way you have a piece of 2 x 12 unscored- I usually add this to my white bits box and use for stamping.


Mat and layer the larger piece panels. I left 1/8 inch all round.

Mat and layer the ‘pop out’ panel , again with a 1/8'' border all round.  Make up topper decorations but it’s easier to leave off any ‘topper’ decorations until you have assembled the card as required.

Tip: You could emboss part or all of these sections of the pop out. 

The back panel of the card is ideal for your sentiment, greeting words etc. If you will use the card straightaway it might be easier to add this panel with a sentiment now.




To add the ‘pop out’ panel. Start by getting the envelope you are going to use for the card - the idea is that the ‘pop out’ doesn't want to overhang the card to the extent it won’t fit in the envelope.

Lay the tall three-fold tall panel to the left of the envelope, leaving a slight gap from the edge.


Place the front section of the pop out front panel on top of the front fold of the main card piece i.e. tuck the other two parts under the front panel.

It is entirely up to you where it sits, but be careful not to put it too low or high as it could cause the card to be unbalanced and not stand up.

Tip: use wet glue that way it gives you some ‘wriggle’ room. I use Collall Multi-purpose glue.

Glue this front panel down, taking care not to place glue on the part that ‘overhangs’ the card.

Turn the card over carefully face down and glue the back panel, this one is much easier to do than the front. Glue as in the photo then fold the back part of the card over. Check its sitting straight, wriggle slightly as required.



Decorate and add toppers as required. I have used CWC 'Sew Lovely' papers and Candi - Very Merry Gold. The decorative toppers are also CWC. Backing paper Papermania. Rear sentiment is Stampin Up!





Variations on card sizes.

Using 12 x 12 card stock I have also made a 5 x 7 version where the card was scored the same at 4 and 8 inch then cut to 7 x 12. Cut the remaining strip at 4 1/4. x 12 Again mountain and valley folds to match bigger piece. Mat and layer. 1/8 inch decrease  all round. This card features just one shade of blue and to add texture and definition all panels are embossed.


Also because not everyone has 12 x 12 card you could use a piece of A4 card.


Cut on the long side to 11 ¼ inch .

Score along the long side at 3 ¾ , 7 ½ inches.

Cut on short side at 5 inches. This will give you two pieces 11 ¼ wide x 5 inches and 11 ¼ x 3 ¼ inches. Cut the mats and layers with a 1/8 inch border all round. All supplies - 'Highland Collection' from a magazine freebie.

This card design can also be up-scaled using A3 cardstock and the shape changed too following the same basic thirds principal.

Enjoy 😊 

;Gill x




Wednesday, 25 August 2021

YVONNE MALLICK - TRIPLE EASEL CIRCLE CARD


Hi there.   Today I am showing my take on a triple circle easel card for this weeks Wednesday Wonder.

For my card, that fits into a C5 envelope, I used:-

3 x 10 1/2 cm fluted circles
6 x  9 cm fluted circles
3 x  8 cm plain circles



Place and glue the edge of one of the smaller fluted circles either side of one of the larger fluted circles... TOP TIP:  I found it easier to position these by laying all three circles on the envelope I was going to use to enable me to gauge the correct position 


Score two of the smaller fluted circles at 1 cm and one of the larger fluted circle at 1 1/2 cm to glue onto the base card as a hinge and each of these three circles at halfway, to make the folding easel mechanism 

Make the hinged scored circle into a mountain fold and glue the bottom half of the scored card to the bottom half of the remaining three fluted circles 



This is the basic card for you to decorate and add the stopper where best suits your personal  design.  I stamped the three plain circles before I stuck them onto the green base card and I used stamped rocks as my stoppers.

This folds down and fits into a C5 envelope



I hope you enjoy having a go at this card as it is much more simple than it looks!  Dont forget to tag me as I would love to see your makes 😊

Happy crafting
Crafty hugs 
Yvonne 😊

I also used:-

Frog and sentiment stamps by Personal Impressions
Reed stamps by inkylicious
Rock stamps by HobbyArt
Flowers by JND
Leaves by Sizzix 


#weeklypromptfloraandfauna   You will need… Cardstock Tape/glue Patterned paper Complimentary dies/die cuts. Make your card with me … Cut yo...